Ozito PMT-004 Instruction Manual Download Page 37

Page: 37 / 40

Cubic Centimetres

No load speed

/min

Revolutions or reciprocation per minute

Decibel level

Read the manual prior to use

Wear safety non-slip boots

Wear safety gloves

Warning

Pull recoil starter to start motor

Do not use any saw blades

Keep bystanders 15m away

Keep bystanders away

Thrown objects can cause

severe injury.

114

Sound pressure level

CHOKE Start position (when engine is cold)

Wear safety goggles, a face guard and

ear protection

Protect the equipment from rain and damp

Extremely hot surface.

Unleaded Petrol 91 RON

Do not smoke.

Always switch off the equipment

and pull out the spark boot plug

before carrying out any

maintenance work.

Beware of recoil

Electric shock can cause fatal injury. Keep a distance of at least

10m from power cables.

Regulator compliance mark (RCM)

Wear safety goggles and ear protection

Risk of fire

RUN Run position

The equipment continues to rotate!

DESCRIPTION OF SYMBOLS

Summary of Contents for PMT-004









































Search results

Summary of Contents for PMT-004

Reviews:

Related manuals for PMT-004

Brands by name

Popular brands

Ozito PMT-004, Instruction Manual

Search results

Summary of Contents for PMT-004

Reviews:

Related manuals for PMT-004

Brands by name

Popular brands