Ozito PMT-004 Instruction Manual Download Page 18 | Manualshive

Page: 18 / 40

background image

18

6. HARNES

Fitting the Harness

1. Fit the harness so that the shoulder pads sit on

the shoulders and the plate hangs down at the

waste.

2. Hook the unit to the

harness.

3. In order to establish the optimum length of the

harness, you should then make a few swinging

movements without starting the engine. Using

the various strap adjusters on the harness,

make adjustments until you achieve the most

comfortable working and cutting position.

4. The harness is fitted with a quick-release

mechanism. Pull the strap if you need to put

down the unit quickly.

SETUP & PREPARATION (cont.)

WARNING!

ALWAYS USE THE HARNESS WHEN WORKING WITH THE

UNIT. ATTACH THE STRAP AS SOON AS YOU HAVE STARTED THE ENGINE

AND IT IS RUNNING IN IDLE MODE. SWITCH OFF THE ENGINE BEFORE

YOU TAKE OFF THE HARNESS.

«
...
16
17
18
19
20
...
»

Summary of Contents for PMT-004









































Reviews:

No comments

Related manuals for PMT-004

Brand: R&S Pages: 150

Brand: R&S Pages: 7

Brand: Facom Pages: 56

Brand: Total Pages: 11

Brand: norbar Pages: 2

Router Table Spline Jig

Brand: Rockler Pages: 8

Universal CPU Holder

Brand: Ergotron Pages: 14

Brand: Zenit Pages: 8

Brand: phytron Pages: 29

WOOD MILL G9959

Brand: Grizzly Pages: 52

Brand: HORN'UP Pages: 20

Brand: Park Tool Pages: 2

Brand: Pattfield Ergo Tools Pages: 2

Brand: Integrated Power Designs Pages: 2

Brand: Fairmount Tools Pages: 8

Brand: Xinpu Pages: 13

Brand: B&G Pages: 2

Brand: Greenlee Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands