Ozito PMT-004 Instruction Manual Download Page 19 | Manualshive

Page: 19 / 40

background image

40:1

Fuel

Oil 40:1

40:1

Fuel

Oil 40:1

19

7. FUEL

WARNING!

PETROL IS VERY FLAMMABLE. DO NOT SMOKE OR CAUSE

ANY SPARKS OR FLAMES NEAR FUEL. MAKE SURE THAT YOU STOP THE

MOTOR AND ALLOW IT TO COOL BEFORE REFUELLING THE ENGINE.

SELECT AN OPEN OUTDOOR AREA FOR FUELLING AND MOVE AT LEAST

3M AWAY FROM THE FUELLING POINT BEFORE STARTING THE ENGINE.

Engine Fuel: Mix at 40:1 Only

Note:

Only use oil that is expressly labelled for use with air-cooled 2-stroke

engines.

Note:

Always transport and store fuels in an approved container (AS2906).

1. Fill fuel mixing bottle with unleaded petrol up to

fuel mark line (for volume required).

2. Add 2-stroke oil up to oil 40:1 mark line. Shake

vigorously for a thorough mix.

3. Remove the fuel tank cap and fill the fuel

tank up to the filler neck with the fuel mix.

Fuel tank capacity: 900ml

4. Fasten the fuel tank cap and clean any

spillage.

Unleaded Petrol (91RON)

2-Stroke Oil

1 litre

25ml

5 litres

125 ml

Fuel Mixing Table

Mixing procedure: 40 parts petrol to 1 part oil

«
...
17
18
19
20
21
...
»

Summary of Contents for PMT-004









































Reviews:

No comments

Related manuals for PMT-004

Brand: Makita Pages: 9

Brand: Icom Pages: 2

Brand: Dake Pages: 24

Brand: HIKOKI Pages: 332

Brand: Jet Pages: 2

Brand: Stanford Research Systems Pages: 42

Brand: Desoutter Pages: 8

Brand: Steel Core Pages: 2

Brand: TDK-Lambda Pages: 22

Brand: Athena Power Pages: 10

Brand: Prym Pages: 2

Brand: Surtek Pages: 16

Brand: Huck Pages: 14

Brand: unicraft Pages: 20

RE-BAR TIER RB397

Brand: Max Pages: 28

Brand: Meec Pages: 20

Brand: Renkforce Pages: 6

Brand: BGS technic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands