Ormec SMLC 160, Installation & Operation Manual

Page: 45 / 66

ServoWire Motion & Logic Controller Manual WAGO I/O Installation & Operation
SMLC ‐ 004a 37
WAGO ‐ 750 ‐ 630/000 ‐ 007 SSI Transmitter Interface, 24 ‐ bit, 83 kHz, graycode w/ status
WAGO ‐ 750 ‐ 630/000 ‐ 005 SSI Transmitter Interface, 15 ‐ bit, 125 kHz, graycode w/ status
WAGO ‐ 750 ‐ 630/000 ‐ 009 SSI Transmitter Interface, 13 ‐ bit, 250 kHz, binary
WAGO ‐ 750 ‐ 630/000 ‐ 012 SSI Transmitter Interface, 13 ‐ bit, 125 kHz, graycode
WAGO ‐ 750 ‐ 631 Incremental Encoder Interface, 16 ‐ bit pos capture, 5 VDC edr power output (note 2)
WAGO ‐ 750 ‐ 637 Incremental Encoder Interface, 32 ‐ bit pos capture, pos compare, 5 VDC edr power
output (see note 2)
WAGO ‐ 750 ‐ 635 Digital Impulse Interface, for magnetostrictive distance measurement sensors
WAGO ‐ 750 ‐ 654 Data Exchange Module
WAGO ‐ 750 ‐ 655 AS ‐ i interface module
WAGO ‐ 750 ‐ 670 Stepper Motor interface module
WAGO ‐ 750 ‐ 671 Stepper Motor interface module
WAGO ‐ 750 ‐ 672 Stepper Motor interface module
WAGO Power Supplies and Accessories
WAGO ‐ 787 ‐ 602 Power Supply 1.3A, 24 VDC output
WAGO ‐ 787 ‐ 612 Power Supply 2.5A, 24 VDC output
WAGO ‐ 787 ‐ 622 Power Supply 5.0A, 24 VDC output
WAGO ‐ 787 ‐ 632 Power Supply 10A, 24 VDC output
WAGO ‐ 787 ‐ 640 Power Supply 10A, 24 VDC output, 3 ‐ phase 230 VAC input
WAGO ‐ 750 ‐ 601 Supply module with fuse, 24 VDC
WAGO ‐ 750 ‐ 612 Supply module, 0 – 230 AC/DC (incl. 5 VDC modules)
WAGO ‐ 750 ‐ 602 Supply module, 24 VDC
WAGO ‐ 750 ‐ 615 Supply module with fuse, 120 VAC
WAGO ‐ 750 ‐ 609 Supply module with fuse, 230 VAC
WAGO ‐ 750 ‐ 622 Binary Spacer Module
WAGO ‐ 750 ‐ 600 End Module
WAGO ‐ 249 ‐ 117 End Stop
WAGO ‐ 247 ‐ PWR Power and Ground Label Strip Pack blue “0V”, blue " ‐ ", red “24V”, red "+", light green
ground symbol, light green “PE”, 100 each
WAGO ‐ 247 ‐ 513/522 I/O Point Numbering Label Strip Pack, digits 00 ‐ 99, 10 each
Table 26, WAGO parts list
NOTE 1: WAGO Fieldbus couplers supply a limited amount of 24 VDC power to the I/O modules, which may not be
sufficient for the application. A Power Supply and Supply Module may be required. Refer to the WAGO Ethernet or
PROFIBUS I&O Manual or the WAGO Web Site for further information.
NOTE 2: Any WAGO Digital I/O modules operating at voltages other than 24 VDC require a Power Supply and
Supply Module with the appropriate voltage rating for input power and isolation. Refer to the WAGO Ethernet or
PROFIBUS I&O Manual or the WAGO Web Site for further information.
NOTE 3: WAGO Analog Output and 2 ‐ Channel AC/DC Output Isolated Relay modules do not pass the power supply
on to other modules in the rack. A supply module will be required for any I/O modules to the right of an Analog
Output or Isolated Relay module in a WAGO I/O system. Refer to the WAGO Ethernet or PROFIBUS I&O Manual or
the WAGO Web Site for further information.