ORiNG IES-3162GC Series User Manual Download Page 40

Page: 40 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

The following table describes the labels in this screen.

Label

Description

RSTP mode

You must enable or disable RSTP function before configuring the

related parameters.

Priority (0-61440)

A value used to identify the root bridge. The bridge with the

lowest value with the highest priority and is selected as the root.

If the value changes, you must restart the switch. The value

must be multiple of 4096 according to the rule of the protocol.

Max Age (6-40)

The number of seconds for a bridge to wait without receiving

Spanning-tree Protocol configuration messages before

reconfiguration. Enter a value between 6 through 40.

Hello Time (1-10)

The time that controls switch sends out the BPDU (Bridge

Protocol Data Unit) packet to check RSTP current status. Enter

a value between 1 through 10.

Forwarding Delay

Time (4-30)

The number of seconds a port to wait before changing from its

learning/listening state to forwarding state. Enter a value

between 4 through 30.

Path Cost

(1-200000000)

The cost of the path to the other bridge from this transmitting

bridge at the specified port. Enter a number 1 through

200000000.

Priority (0-240)

Decide which port should be blocked by setting the priority in

LAN. Enter a number 0 through 240. The value of priority must

be the multiple of 16

Admin P2P

Some of the rapid state transactions that are possible within

RSTP are dependent upon whether the port concerned can only

be connected to exactly one other bridge (i.e., It is served by a

point-to-point LAN segment), or it can be connected to two or

more bridges (i.e., It is served by a shared medium LAN

segment). This function allows the P2P status of the link to be

manipulated administratively. True means P2P enabled. False

means P2P disabled.

Admin Edge

The port directly connected to end stations, and it cannot create

bridging loop in the network. To configure the port as an edge

port, set the port to “

True

”.

Admin Non STP

The port includes the STP mathematic calculation. STP

algorithm is included for “

True

“ setting, STP algorithm is not

included for “

False

“ setting.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands