ORiNG IES-3162GC Series User Manual Download Page 92

Page: 92 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

spanning tree

considers the path

cost when selecting

an interface to place

into the forwarding

state.

stp-path-priority

[Port Priority]

Use the spanning-tree

port-priority interface

configuration

command to configure

a port priority that

is used when two

switches tie for

position as the root

switch.

switch(config)#interface fastEthernet

switch(config-if)# stp-path-priority

127

stp-admin-p2p

[Auto|True|False]

Admin P2P of STP

priority on this

interface.

switch(config)#interface fastEthernet

switch(config-if)# stp-admin-p2p

Auto

stp-admin-edge

[True|False]

Admin Edge of STP

priority on this

interface.

switch(config)#interface fastEthernet

switch(config-if)# stp-admin-edge

True

stp-admin-non-stp

[True|False]

Admin NonSTP of

STP priority on this

interface.

switch(config)#interface fastEthernet

switch(config-if)# stp-admin-non-stp

False

Show spanning-tree

Display a summary of

the spanning-tree

states.

switch>show spanning-tree

no spanning-tree

Disable spanning-tree. switch(config)#no spanning-tree

6.7 Commands Set List

—QoS command set

IES-3162GC Commands Level Description

Example

qos policy

Select QOS policy

switch(config)#qos policy

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands