ORiNG IES-3162GC Series User Manual Download Page 17

Page: 17 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

EB Management

5.1 Configuration by Web Browser

This section introduces the configuration by Web browser.

5.1.1 About Web-based Management

An embedded HTML web site resides in flash memory on the CPU board. It contains

advanced management features and allows you to manage the switch from anywhere on the

network through a standard web browser such as Microsoft Internet Explorer.

The Web-Based Management function supports Internet Explorer 5.0 or later. It is based

on Java Applets with an aim to reduce network bandwidth consumption, enhance access

speed and present an easy viewing screen.

Note:

By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to explicitly modify

the browser setting in order to enable Java Applets to use network ports

Preparing for Web Management

The default value is as below:

IP Address:

192.168.10.1

Subnet Mask:

255.255.255.0

Default Gateway:

192.168.10.254

User Name:

admin

Password:

admin

System Login

Launch the Internet Explorer.

Type http:// and the IP address of the switch. Press “

Enter

”.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands