ORiNG IES-3162GC Series User Manual Download Page 47

Page: 47 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

The following table describes the labels in this screen.

Label

Description

VLAN Operation

Mode

Configure VLAN Operation Mode: disable, Port Base,802.1Q

GVRP Mode

Enable/Disable GVRP function.

Management VLAN

Management VLAN provide network administrator a secured

VLAN to management Switch. Only the devices in the

management VLAN can access the switch.

Link type

There are 3 types of link type:

Access Link:

single switch only,

allows you to group ports by

setting the same VID.

Trunk Link:

extended application of

Access Link

, allows you to

group ports by setting the same VID with 2 or more switches.

Hybrid Link:

Both

Access

Link

and

Trunk Link

are available.

Hybrid(QinQ) Link:

enable QinQ mode

，

allow you to insert one

more VLAN tag in a original VLAN frame.

Untagged VID

Set the port default VLAN ID for untagged devices that connect to

the port. The range is 1 to 4094.

Tagged VIDs

Set the tagged VIDs to carry different VLAN frames to other

switch.

Apply

Click “

Apply

” to activate the configurations.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands