ORiNG IES-3162GC Series User Manual Download Page 91

Page: 91 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

from the root switch

within this interval, it

recomputed the

Spanning Tree

Protocol (STP)

topology.

spanning-tree

hello-time

[seconds]

Use the spanning-tree

hello-time global

configuration

command to specify

the interval between

hello bridge protocol

data units (BPDUs).

switch(config)#spanning-tree

hello-time 3

spanning-tree

forward-time

[seconds]

Use the spanning-tree

forward-time global

configuration

command to set the

forwarding-time for the

specified

spanning-tree

instances. The

forwarding time

determines how long

each of the listening

and

learning states last

before the port begins

forwarding.

switch(config)# spanning-tree

forward-time 20

stp-path-cost

[1to200000000]

Use the spanning-tree

cost interface

configuration

command to set the

path cost for Spanning

Tree

Protocol (STP)

calculations. In the

event of a loop,

switch(config)#interface fastEthernet

switch(config-if)#stp-path-cost 20

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands