ORiNG IES-3162GC Series User Manual Download Page 73

Page: 73 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

TX GOOD Packet

The number of good packets sent by this port.

TX Bad Packet

The number of bad packets sent by this port.

RX GOOD Packet

The number of good packets received by this port.

RX Bad Packet

The number of bad packets received by this port.

TX Abort Packet

The number of packets aborted by this port.

Packet Collision

The number of times a collision detected by this port.

Clear

Clear all counters.

Help

Show help file.

5.1.14.4 Port Monitoring

Port monitoring function supports TX (egress) only, RX (ingress) only, and both TX/RX

monitoring. TX monitoring sends any data that egress out checked TX source ports to a

selected TX destination port as well. RX monitoring sends any data that ingress in checked

RX source ports out to a selected RX destination port as well as sending the frame where it

normally would have gone. Note that keep all source ports unchecked in order to disable port

monitoring.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands