ORiNG IES-3162GC Series User Manual Download Page 25

Page: 25 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

Period

ending time. Both will be different each year.

Daylight Saving

Offset

Set up the offset time.

Switch Timer

Display the switch current time.

Apply

Click “

Apply

” to activate the configurations.

5.1.4.5

LLDP

LLDP (Link Layer Discovery Protocol) function allows the switch to advertise its information

to other nodes on the network and store the information it discovers.

LLDP configuration interface

The following table describes the labels in this screen.

Label

Description

LLDP Protocol

“

Enable

” or “

Disable

” LLDP function.

LLDP Interval

The interval of resend LLDP (by default at 30 seconds)

Apply

Click

“

Apply

” to activate the configurations.

Help

Show help file.

5.1.4.6

Auto Provision

Auto Provision allows you to update the switch firmware automatically. You can put

firmware or configuration file on TFTP server. When you reboot the switch, it will upgrade

automatically. Before updating, make sure you have your TFTP server ready and the

firmware image and configuration file is on the TFTP server.

Auto Provision interface

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands