ORiNG IES-3162GC Series User Manual Download Page 61

Page: 61 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

Apply

Click “

Apply

” to activate the configurations.

Help

Show help file.

5.1.12.2 Port Security

Port security is to add static MAC addresses to hardware forwarding database. If port

security is enabled at

Port Control

page, only the frames with MAC addresses in this list will

be forwarded, otherwise will be discarded.

Port Security interface

The following table describes the labels in this screen.

Label

Description

MAC Address

Input MAC Address to a specific port.

Port NO.

Select port of switch.

Add

Add an entry of MAC and port information.

Delete

Delete the entry.

Help

Show help file.

5.1.12.3 MAC Blacklist

MAC Blacklist can eliminate the traffic forwarding to specific MAC addresses in list. Any

frames forwarding to MAC addresses in this list will be discarded. Thus the target device will

never receive any frame.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands