ORiNG IES-3162GC Series User Manual Download Page 45

Page: 45 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

VLANs

Set which VLAN will belong which instance

Proprietary (0-61440)

A value used to identify the root bridge. The bridge with the

lowest value has the highest priority and is selected as the root.

If the value changes, You must reboot the switch. The value

must be multiple of 4096 according to the protocol standard rule.

Apply

Click “

Apply

” to activate the configurations.

MSTP Instance Port interface

Label

Description

Instance

Set the instance’s information except CIST

Port

Selecting the port that you want to configure.

Priority (0-240)

Decide which port should be blocked by priority in LAN. Enter a

number 0 through 240. The value of priority must be the multiple

of 16

Path Cost

(1-200000000)

The cost of the path to the other bridge from this transmitting

bridge at the specified port. Enter a number 1 through

200000000.

Apply

Click “

Apply

” to set the configurations.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands