ORiNG IES-3162GC Series User Manual Download Page 56

Page: 56 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

Label

Description

COS/802.1p

COS (Class Of Service) is well known as 802.1p. It describes

that the output priority of a packet is determined by user priority

field in 802.1Q VLAN tag. The priority value is supported

0to7.COS value map to 4 priority queues: High, Middle, Low, and

Lowest.

COS Port Default

When an ingress packet has not VLAN tag, a default priority value

is considered and determined by ingress port.

Help

Show help file.

Apply

Click “

Apply

” to activate the configurations.

TOS/DSCP interface

Label

Description

TOS/DSCP

TOS (Type of Service) is a field in IP header of a packet. This

TOS field is also used by Differentiated Services and is called the

Differentiated Services Code Point (DSCP). The output priority

of a packet can be determined by this field and the priority value is

supported 0 to 63. DSCP value map to 4 priority queues: High,

Middle, Low, and Lowest.

Apply

Click “

Apply

” to activate the configurations.

Help

Show help file.

Summary of Contents for IES-3162GC Series









































































































Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands

ORiNG IES-3162GC Series, User Manual

Search results

Summary of Contents for IES-3162GC Series

Reviews:

Related manuals for IES-3162GC Series

Brands by name

Popular brands