Oracle Sun Server X4-4 Installation Manual Download

Page: 9 / 148

Using This Documentation

This section describes how to get the latest firmware and software for the system,

documentation and feedback, and a document change history.

■

“Sun Server X4-4 Model Naming Convention” on page 9

■

“Getting the Latest Firmware and Software” on page 9

■

“Documentation and Feedback” on page 10

■

“About This Documentation” on page 10

■

“Support and Training” on page 10

■

“Contributors” on page 10

■

“Change History” on page 11

Sun Server X4-4 Model Naming Convention

The Sun Server X4-4 name identifies the following:

■

X identifies an x86 product.

■

The first number, 4, identifies the generation of the server.

■

The second number, 4, identifies the number of processor sockets in the server.

Getting the Latest Firmware and Software

Firmware, drivers, and other hardware-related software for each Oracle x86 server are updated

periodically.

You can obtain the latest version in one of following ways:

■

Oracle System Assistant – This is a factory-installed option for Sun Oracle x86 servers. It

has all the tools and drivers you need and resides on an internal USB flash stick.

Using This Documentation

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands