Oracle Sun Server X4-4 Installation Manual Download

Page: 11 / 148

Change History

Contributors: Kenny Tung, Barry Wright, David Savard

Change History

The following lists the release history of this documentation set:

■

April 2014. Initial publication.

■

May 2014. Updated

Product Notes

for SW 1.0.1. Updated

Product Notes

Installation Guide

and

Service Manual

information for the 8 GB DIMM which will no longer be orderable as

of June 2014.

■

October 2014. Updated

Product Notes

for SW 1.1.0. Updated

Installation Guide

and

Sun

Server X4-4 Installation Guide for Linux Operating System

information to add support for

the Oracle Linux Fault Management Architecture software available with Oracle Hardware

Management Pack 2.3. Minor editorial updates to

Sun Server X4-4 Installation Guide for

Windows Operating System

■

January 2015. Updated

Product Notes

for SW 1.1.1.

■

August 2015. Updated

Product Notes

for SW 1.2. Updated the

Service Manual

information

for the fan module replacement. Updated the

Installation Guide

for minor technical edits.

■

September 2015. Updated

Product Notes

for SW 1.2.1.

■

October 2015. Updated

Product Notes

to add note about important updates. Removed

information in all books about obtaining physical media for Oracle software.

Using This Documentation

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands