Oracle Sun Server X4-4 Installation Manual Download

Page: 96 / 148

Configure RAID in UEFI BIOS Boot Mode

Configuring RAID Using the BIOS With the Sun

Storage 6 Gb SAS PCIe RAID Internal HBA

The BIOS RAID configuration utilities support configuring RAID with the server set to UEFI

BIOS Boot Mode and Legacy BIOS Boot Mode. A separate utility is provided for each boot

mode.

Note -

Some operating systems and virtual machine software only support the Legacy BIOS

Boot Mode. For a list of operating systems and virtual machine software that do not support

UEFI BIOS Boot Mode, see

“UEFI BIOS” on page 24

■

“Configure RAID in UEFI BIOS Boot Mode” on page 96

■

“Configure RAID in Legacy BIOS Boot Mode” on page 101

Configure RAID in UEFI BIOS Boot Mode

Power on or reset the server.

For example, to reset the server:

■

From the local server,

press the Power button (approximately 1 second) on the front panel

of the server to power off the server, then press the Power button again to power on the

server.

■

From the Oracle ILOM web interface,

select

Host Management > Power Control

, then

select

Reset

from the

Select Action

list box.

■

From the Oracle ILOM CLI,

type:

reset /System

The BIOS screen appears.

When prompted in the BIOS screen, press F2 to access the BIOS Setup Utility.

After a few moments, the BIOS Setup Utility appears.

Use the right arrow key to navigate to the Advanced menu.

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands