Oracle Sun Server X4-4 Installation Manual Download

Page: 43 / 148

Install Cable Management Arm

You will hear an audible click.

Caution -

Equipment damage or personal injury. Verify that the server is securely mounted in

the rack and that the slide-rail locks are engaged with the mounting brackets before continuing.

Install Cable Management Arm

The cable management arm (CMA) is an optional assembly that you can use to route the server

cables in the rack.

Unpack the CMA parts.

Take the CMA to the back of the equipment rack and ensure that you have

adequate room to work around the back of the server.

Note -

References to “left” or “right” in this procedure assume that you are facing the back of

the equipment rack.

Installing the Server Into a Rack

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands