Oracle Sun Server X4-4 Installation Manual Download

Page: 94 / 148

Configure RAID in UEFI BIOS Boot Mode

■

From the local server,

press the Power button (approximately 1 second) on the front panel

of the server to power off the server, then press the Power button again to power on the

server.

■

From the Oracle ILOM web interface,

select

Host Management > Power Control

, then

select

Reset

from the

Select Action

list box.

■

From the Oracle ILOM CLI,

type:

reset /System

The BIOS screen appears.

When prompted in the BIOS screen, press F2 to access the BIOS Setup Utility.

After a few moments, the BIOS Setup Utility appears.

Use the right arrow key to navigate to the Advanced menu.

The Advanced menu appears.

Use the up and down arrow keys to navigate to the LSI SAS2 MPT Controller

menu option, and press Enter.

Use the BIOS configuration utility to configure RAID on the server.

For instructions on how to use the BIOS configuration utilities to configure RAID in UEFI

BIOS Boot Mode, refer to instructions for creating a bootable drive on x86/64 systems in the

Sun Storage 6 Gb SAS PCIe HBA, Internal Installation Guide For HBA Models SGX-SAS6-

INT-Z and SG-SAS6-INT-Z

at:

http://docs.oracle.com/cd/E19337-01/index.html

Next Steps

■

“Set Up an Operating System and Drivers” on page 104

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands