Oracle Sun Server X4-4 Installation Manual Download

Page: 104 / 148

Configure RAID in Legacy BIOS Boot Mode

The Virtual Drives screen appears.

Select the virtual drive that you want to make bootable.

Click Set Boot Drive, then click Go.

For more information on performing this task, refer to the

LSI MegaRAID SAS Software User's

Guide

located at:

http://www.lsi.com/sep/Pages/oracle/sg_x_sas6-r-rem-z.aspx

Set Up an Operating System and Drivers

You can configure a preinstalled operating system (OS), or install a supported OS for your

server. The following table describes how to access information about installing or configuring

an OS.

What do you want to do?

Refer to this documentation

Configure a factory preinstalled OS

■

“Configuring the Preinstalled Oracle Solaris

OS” on page 107

104

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands