manualshive.com logo in svg

Oracle Sun Server X4-4, Installation Manual

Share
Download
Oracle Sun Server X4-4 Installation Manual Download Page 107

Configuring the Preinstalled Oracle Solaris OS

At initial release, the Sun Server X4-4 offers the option of a preinstalled Oracle Solaris

11.1.x operating system (OS) image on your server. If you purchased this option, finish the

installation by configuring the preinstalled software. The preinstalled OS image contains all of

the necessary drivers for your server model.

Note - 

For up-to-date information about supported versions of the preinstalled Oracle Solaris

OS, see the 

Sun Server X4-4 Product Notes

 at 

http://www.oracle.com/goto/X4-4/docs

.

Perform the procedures in the following sections in the order listed:

Step

Task

Links

1

Fill out the configuration worksheet for your server

environment.

“Oracle Solaris OS Configuration

Worksheet” on page 107

2

Configure the preinstalled Oracle Solaris OS.

“Configure the Preinstalled Oracle Solaris

Operating System” on page 110

3

Review the Oracle Solaris OS documentation for

information about registering, updating and using

the Oracle Solaris OS.

“Oracle Solaris Operating System

Documentation” on page 112

Oracle Solaris OS Configuration Worksheet

Before you start to configure the preinstalled Oracle Solaris Operating System, review the

applicable limitations on RAID configurations. Then complete the worksheet for the Oracle

Solaris configuration.

Before you begin configuring the operating system, use the configuration worksheet in the

following table to gather the information that you will need. You need to collect only the

information that applies to your application of the system.

Configuring the Preinstalled Oracle Solaris OS

107

Summary of Contents for Sun Server X4-4





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands