Seite :
11
Kodex :
000006BD
Kap.:
1
Die vorliegende Unterlage ist Eigentum des Herstellers u/o seines V
ertreters und darf auf keinen Fall vervielfältigt, als auch nicht an Dritte ohne Einverständnis weitergegeben werden.
EINSAtZBEREICH
Die Firma OP s.r.l. übernimmt keine haftung für Schäden jeglicher art,
die auf nicht korrekte Operationen oder leichtigkeit zurückzuführen
sind.
Die Maschine DARF NICHT von unerfahrenem Personal
benutzt werden oder von erfahrenem Personal, wel-
ches jedoch Operationen an der Maschine durchführt,
die nicht mit den Hinweisen in dem hier vorliegenden
Handbuch und den beigelegten Unterlagen überein-
stimmen.
Es ist absolut verboten, die Maschine in einem nicht
mit dem Einsatzbereich konformem Feld zu gebrau-
chen.
Normalgebrauch
Die Maschine ist so konzipiert, dass sie nur von einem eingeführten
Bediener geführt wird, der über die restlich bestehenden Gefahren
informiert ist; bei Betrieb, das arbeitsgebiet oder Zone ist der Fontal-
bereich oder Vorderbereich der Maschine, der entsprechend ausgelegt
ist, damit man in Sicherheit arbeiten kann.
Die folgenden handbuch beschrieben Maschine ist für folgende arbeiten
entwickelt worden:
Einführung über ein Presssystem von Metallarmaturen mit
Öldynamikschläuchen bei hohem und niedrigem Druck (die
Armaturen und die Schläuche müssen bestimmte Eigenschaften
u/o Materialien besitzen, die bei Bestellung u/o durch den Kun-
den exklusiv bestimmt werden).
Die einfachheit der Maschinenkommandos trägt dazu bei, dass sie von
einem sehr großen Kundenkreis benutzt werden kann.
Das elektrosystem (eS Version) verfügt über drei arbeitsprogramme:
Manuell, halbautomatisch und weitere Funktionen, um das Pressen
und einführen zu vereinfachen und zu beschleunigen.
Der Anwendungsbereich der Maschine muss innerhalb
der Einschränkungen, die im Verkaufsvertrag be-
stimmt, in den Tabellen “Technische Eigenschaften“
und Anwendungsbereich- Einschränkungen“ sowie
im ganzen Handbuch aufgeführt sind, liegen..
N.B. Der Bediener muss einen entsprechende Abstand
halten, um die entsprechenden Arbeitsgänge ausfüh-
ren zu können; er muss jedoch so weit entfernt sein,
damit nicht ungewollt Hände oder Körperteile in die
Schneidezone gelangen.
in diesem handbuch sind die restrisiken, die in der entwicklungsphase
nicht beseitigt werden konnten, aufgelistet und beschrieben (siehe
„tabelle restrisiken”).
aus Sicherheitsgründen dürfen sich während der Bearbeitungs-
tätigkeiten sich in der nähe der Maschine, außer dem Bediener, keine
anderen Personen aufhalten. Von dieser Vorschrift ist das
Wartungspersonal ausgeschlossen, dessen anwesenheit ausdrücklich
vom leiter der Betriebstätigkeit genehmigt ist.
ACHTUNG!
Die nicht nach Vorgaben gebrauchten
Werkzeuge können sehr gefährlich
sein und Schäden an Körperteile verur-
sachen; diese dürfen niemals mit den
bewegliche Maschinenteile oder in den
entsprechenden Bereichen in Kontakt
kommen.