manualshive.com logo in svg

Omron sysmac EtherNet/IP NJ Series, Connection Manual, Page: 61 / 68

Share
Download
Omron sysmac EtherNet/IP NJ Series Connection Manual Download Page 61

7

．

EtherNet/IP Connection Procedure 

  58 

7.5.  EtherNet/IP Communication Status Check 

Confirm that the EtherNet/IP tag data links perform normally.   

 

7.5.1.  Checking the Connection Status 

Check the EtherNet/IP connection status.   

 

1 

Turn ON Communications power 

supply for DeviceNet and I/O power 

supply for DeviceNet Slave. 

 

2 

Check with LED indicators on 

Controller that the tag data links 

perform normally.   

 

The LED indicators in normal status 

are as follows:   

NET RUN: Green lit 

NET ERR: Not lit 

LINK/ACT: Yellow flashing   

(Flashing while packets are being 

sent and received.) 

 
*The NX-series Controllers also 

have the same LED indicator 
status.   

 

 

 

 

3 

Check the LED indicators on 

netTAP. 

 

The LED indicators in normal status 

are as follows:   

SYS  : Green lit 

APL  : Green lit 

MS  : Green lit 

NS  : Green lit 

LINK L/A 

: Green lit 

ACT Rx/Tx : Yellow flashing 

MNS : Green lit 

 

 

*The LED indicators on DeviceNet 

Slave are as follows:   

MS : Green lit 
NS : Green lit 

netTAP 

 

 

DeviceNet Slave 

 

MNS (DeviceNet) 

MS (EtherNet/IP) 

NS (EtherNet/IP) 

Summary of Contents for sysmac EtherNet/IP NJ Series





































































Reviews:

No comments