manualshive.com logo in svg

Omron sysmac EtherNet/IP NJ Series, Connection Manual, Page: 58 / 68

Share
Download
Omron sysmac EtherNet/IP NJ Series Connection Manual Download Page 58

7

．

EtherNet/IP Connection Procedure 

  55 

3 

The Edit Connection Dialog 

Box is displayed.   

Make the settings (listed in the 

following table) in the 

Connection I/O Type

, 

Originator Device

 and 

Target 

Device 

Fields.   

 

Click

 Regist

.   

 

 

■Editing

 settings for connections   

Connection I/O Type 

Data, In/Out 

Originator Device 

 

Target Device 

Input Tag Set 

Connection Type 

<- 

Output Tag Set 

EIP002_IN-[2Byte] 

Point to Point connection 

Input_101-[2Byte] 

Output Tag Set 

Connection Type 

-> 

Input Tag Set 

EIP002_OUT-[2Byte] 

Point to Point connection 

Output_100-[2Byte] 

 

 

4 

The Edit Connection Dialog 

Box is displayed again.   

Click 

Close

.   

 

5 

The Edit Device Parameters 

Dialog Box is displayed.   

Check that the connections set 

for 192.168.250.2 are 

registered.   

 

Click 

OK

. 

 

Summary of Contents for sysmac EtherNet/IP NJ Series





































































Reviews:

No comments