manualshive.com logo in svg

Omron sysmac EtherNet/IP NJ Series, Connection Manual, Page: 12 / 68

Share
Download
Omron sysmac EtherNet/IP NJ Series Connection Manual Download Page 12

5

．

Applicable Devices and Device Configuration 

  9 

 

Additional Information 

For information on power supply specifications of the DeviceNet Slave and wiring methods, 

refer to the 

DRT2 Series DeviceNet

TM 

Slaves OPERATION MANUAL

 (Cat. No. W404). 

 

 

Additional Information 

The system configuration in this guide uses USB for the connection between the personal 

computer and the Controller. For information on how to install the USB driver, refer to 

A-1 

Driver Installation for Direct USB Cable Connection

 of the 

Sysmac Studio Version 1 

Operation Manual 

(Cat. No. W504).   

For NX1P2 Controllers, there is no need to install the USB driver because they do not have 

USB ports.   

 

 

Additional Information 

The NX1P2 Controller, if used, must be connected to your personal computer with an 

Ethernet cable. For information on how to connect the cable, refer to 

6-2 Going Online with a 

Controller 

of the 

Sysmac Studio Version 1 Operation Manual 

(Cat. No. W504).   

 

 

Additional Information 

The system configuration in this guide uses USB for the connection between the personal 

computer and the netTAP. For information on how to install the USB driver, refer to the 

User 

Manual Software Installation Gateway Solutions

 (DOC100315UM07EN). 

 

 

 

Summary of Contents for sysmac EtherNet/IP NJ Series





































































Reviews:

No comments