manualshive.com logo in svg

Omron sysmac EtherNet/IP NJ Series, Connection Manual, Page: 35 / 68

Share
Download
Omron sysmac EtherNet/IP NJ Series Connection Manual Download Page 35

7

．

EtherNet/IP Connection Procedure 

  32 

4 

The Project Properties Dialog 

Box is displayed.   

 
*In this guide, "New Project" is 

used as the project name.     

 

Check that the device used is 

shown in the 

Category 

and 

Device

 Fields of Select Device.   

 

 

 

Select an applicable version 

from the pull-down list of 

Version.   

 
*Although 1.18 is selected as an 

example in this guide, select 
the version you actually use.   

 

 

5 

Click 

Create

.   

 

6 

The New Project is displayed.   

 

The following panes are 

displayed in the window.   

Left: Multiview Explorer 

Top right: Toolbox 

Bottom right: Controller Status Pane 

Top middle: Edit Pane 

The following tabs are displayed 

in the bottom middle of the 

window.   

Output Tab Page 

Build Tab Page 

 

 

Controller 

Status Pane 

Toolbox 

Edit Pane

 

Multiview 

Explorer

 

Build Tab Page

 

Output Tab Page

 

Summary of Contents for sysmac EtherNet/IP NJ Series





































































Reviews:

No comments