manualshive.com logo in svg

Omron sysmac EtherNet/IP NJ Series, Connection Manual, Page: 18 / 68

Share
Download
Omron sysmac EtherNet/IP NJ Series Connection Manual Download Page 18

7

．

EtherNet/IP Connection Procedure 

  15 

4 

Connect netTAP power supply 

to X1 on netTAP. 

 
*For details on connecting the 

power supply, refer to the 

User 

Manual netTAP NT 100 
Gateway Devices

 

(DOC081001UM18EN). 

 

5 

Check the positions of the 

hardware switches and 

connector on DeviceNet Slave 

by referring to the figure on the 

right. 

 

6 

Set the node address (MAC ID) 

using Rotary switches on 

DeviceNet Slave. 

 

X10: 

0

 

X1:

 1

 

 
*The node address (MAC ID) is 

set to 1.   

 

7 

Connect I/O power supply to 

DeviceNet Slave, and wire the 

I/O for checking sent and 

received data. 

 
*For more information on I/O 

wiring of DRT2-OD16 and 
XWT-ID16, refer to the 

DRT2 

Series DeviceNet

 TM

 Slaves 

OPERATION MANUAL

 (Cat. 

No. W404). 

 
*In this guide, an output signal is 

sent from Controller to bit 0 of 
DRT2-OD16, and then the 
signal goes to bit 0 of 
XWT-ID16 to return to 
Controller. Here, the I/O is 
wired in order to check that the 
signal can be returned and 
received by Controller. 

 

netTAP power supply 

Communications connector 

Rotary switches 

DRT2-OD16 

XWT-ID16 

I/O power supply 

Summary of Contents for sysmac EtherNet/IP NJ Series





































































Reviews:

No comments