manualshive.com logo in svg

Omron sysmac EtherNet/IP NJ Series, Connection Manual, Page: 24 / 68

Share
Download
Omron sysmac EtherNet/IP NJ Series Connection Manual Download Page 24

7

．

EtherNet/IP Connection Procedure 

  21 

17 

After performing step 16, the 

following gateway and firmware 

are displayed. 

 

- Required gateway:   

NT 100-RE-DN 

- Available Firmware: 

NTEISDNM.NXF 

 

18 

If the available firmware 

displayed in step 17 is not 

downloaded, use the following 

steps to download the firmware. 

 

Click 

Browse

 to the right of 

Available Firmware. 

 

*There is no need to perform 

steps from 18 to 22 if the 
available firmware is already 
downloaded to netTAP.   

In that case, click 

OK

 at the 

bottom of the Settings Pane to 
finish the gateway 
configuration of netTAP. 

 

 

 

 

 

 

 

 

 

19 

Select 

NTEISDNM.NXF

 from 

the Select Firmware File Dialog 

Box.   

Click 

Open

. 

 

20 

The 

Download

 Button is now 

available. Click 

Download

 to 

download the firmware into 

netTAP. 

 

21 

The dialog box on the right is 

displayed. Confirm that there is 

no problem, and click 

Yes

.   

 

The firmware download starts. 

 

…

 

Summary of Contents for sysmac EtherNet/IP NJ Series





































































Reviews:

No comments