Omron SYSMAC C200H-PID0 Series, Operation Manual

Page: 48 / 68

40
4-1-3 Table of Commands
The command codes shown below are set in bits (Wd n) 07 to 00 when the
SW2-1 (switching memory contents) on the front panel is set in the Normal posi-
tion.
EEPROM Write/Read Commands
Parameter Com-
mand
Write Read Loop
no.
Bank
no.
Actual data
range
SV data
range
Default value
Set point (see note 3) 0 0 Yes Yes Yes Yes Scaling lower limit to scaling
upper limit 0 EU
Manual output volume
(see note 6) 0 1 Yes Yes Yes No -5 to 105% F005 to
0105 0%
Execution bank number 0 2 Yes Yes Yes No 1 to 8 0001 to
0008 1
Alarm SV 1 (see notes
3, 4) 0 3 Yes Yes Yes Yes Alarm mode
1, 4, 5:
0 to 9999
0000 to
9999
0 EU
Alarm SV 2 (see notes
3, 4) 0 4 Yes Yes Yes Yes
0 to 9999
Other:
–999 to 9999
9999
F999 to
9999
0 EU
Input shift value (see
note 3) 0 5 Yes Yes Yes Yes –999 to 9999 F999 to
9999 0 EU
Proportional band (see
note 1) 0 6 Yes Yes Yes Yes 0.0 to 999.9 0000 to
9999 10.0 %FS
Integral (reset) time
(see note 1) 0 7 Yes Yes Yes Yes 0 to 9999 s 240 s
Derivative (rate) time
(see note 1) 0 8 Yes Yes Yes Yes 0 to 9999 s 40 s
Decimal point position 1 2 Yes Yes Yes No 0 to 3 0000 to
0003 1
Scaling lower limit 1 3 Yes Yes Yes No -999 to (scaling upper limit
value – 1 digit) 0
Scaling upper limit 1 4 Yes Yes Yes No (Scaling lower limit + 1 digit)
to 9999 100.0
Control period (see note
1) 1 7 Yes Yes Yes No 1 to 99 s 0001 to
0099 20 s
Hysteresis (see note 2) 1 8 Yes Yes Yes Yes 0.0 to 100.0 0000 to
1000 0.2 %FS
Alarm hysteresis (see
note 4) 1 9 Yes Yes Yes No 0.0 to 100.0 0000 to
1000 0.1 %FS
Digital filter 1 E Yes Yes Yes No 0 to 100 0000 to
0100 0 s
Control output variable
monitor 2 0 No Yes Yes No –5.0 to
105.0% F050 to
1050 0.0%
Auto-tuning start/stop
(see note 1) 2 1 Yes No Yes No --- AT start =
0001
AT stop =
0000 ---
Copy bank 2 2 Yes No Yes No --- ---
Input-type monitor 2 3 No Yes No No 0 to 9 0000 to
0009 Setting for
SW202
Alarm 1 mode 2 4 Yes Yes Yes No 0 to 9 0000 to
0009 2
Alarm 2 mode 2 5
0009
Yes: Possible.
No: Not possible or not required.
Note 1. Only when advanced PID control is selected. (Switch 203-1 = OFF)
2. Only when ON/OFF control is selected. (Switch 203-1 = ON)
Memory Allocation Section 4-1