Omron NX-ILM400, User Manual

Page: 167 / 176

A - 41
Appendices
NX-series IO-Link Master Unit User’s Manual (W567)
A-6 V
ersion
Informa
tion
with C
o
m
m
un
icati
ons
Cou
p
ler Un
it
s
A
A-6-2 Connection to an
EtherNet/IP Co
upler Unit
 When Using a CS/CJ/CP-series PLC
The items that are used in the version combination tables are given below.
The version combination table is given below.
• With the combinations of the unit versions/versions shown below, you can use the functions that
are supported by the unit version of the Unit model. Use the unit versions/versions (or the
later/higher unit versions/versions) that correspond to the NX Unit models and the unit versions.
You cannot use the specifications that were added or changed for the relevant NX Unit models
and the unit versions unless you use the corresponding unit versions/versions.
• Depending on the type and model of the Unit to which the NX Unit is connected, some Units do
not have the corresponding versions given in the table. If a Unit does not have the specified ver-
sion, support is provided by the oldest available version after the specified version. Refer to the
user's manuals for the specific Units for the relation between models and versions.
• If you use the corresponding unit versions/versions given in the following table or later/higher ver-
sions, refer to the version information in the user’s manual for the Communications Coupler Unit,
and CPU Unit.
The following table shows the relationship between the unit versions/versions of the NX Units, Commu-
nications Coupler Units, CPU Units, Industrial PCs, Sysmac Studio, NX-IO Configurator, and CX-Con-
figuratorFDT for changes in or additions to the functions.
A description is provided for each Controller that is used.
NX Unit Corresponding unit version/version
Model Unit version
EtherNet/IP
Coupler Unit
Sysmac Studio
NX-IO Configu-
rator
CX-Configura-
torFDT
Model numbers
of NX Units. Unit versions of
NX Units. Unit versions of
Ether- Net/IP
Coupler Units
that are com-
patible with the
NX Units. Sysmac Studio
versions that
are compatible
with the NX
Units, Ether-
Net/IP Coupler
Units. NX-IO Configu-
rator versions
that are com-
patible with the
NX Units, Eth-
erNet/IP Cou-
pler Units. The version of
the CX-Configu-
ratorFDT that
supports the
IO-Link Master
Unit.
NX Unit
Corresponding unit version/version
*1
*1. Refer to the user's manual of the EtherNet/IP Coupler Unit for the unit versions of CPU Units and Ether-
Net/IP Units corresponding to EtherNet/IP Coupler Units.
Models Unit version
EtherNet/IP
Coupler Unit
Sysmac Studio
NX-IO Configu-
rator
*2
*2. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, connection is supported only for a
connection to the peripheral USB port on the EtherNet/IP Coupler Unit. You cannot connect by any other
path. If you need to connect by another path, use an EtherNet/IP Coupler Unit with unit version 1.2 or later.
CX-Configura-
torFDT
NX-ILM400 Ver.1.0 Ver.1.0 Ver.1.16 Ver.1.00
Ver.2.2
*3
*3. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, connection is supported only for a
connection to the peripheral USB port on the EtherNet/IP Coupler Unit. You cannot connect by any other
path. If you need to connect by another path, use an EtherNet/IP Coupler Unit with unit version 1.2 or later
and CX-ConfiguratorFDT with version 2.4 or higher.
Ver.1.1 Ver.1.20 Ver.1.01
Functions That Were Added or Changed for Each Unit Version