manualshive.com logo in svg

OmniSwitch os6900, Network Configuration Manual, Page: 218 / 942

Share
Download
OmniSwitch os6900 Network Configuration Manual Download Page 218

Configuring Virtual Chassis

Configuring Virtual Chassis

page 9-20

OmniSwitch AOS Release 7 Network Configuration Guide

June 2013

Configuring the Virtual Chassis Group Identifier

A virtual chassis group identifier must be assigned to each of the switches that will form the Virtual Chas-
sis group. Each of these switches must use the same group identifier, which identifies the switch as 
belonging to that virtual chassis group. 

The 

virtual-chassis chassis-group

 command is used to configure the same group identifier for each 

switch within the virtual chassis group. For example:

-> virtual-chassis chassis-group 1

By default, the virtual chassis group identifier is set to “0”. In a network environment where more than one 
virtual chassis group may exist, configure each virtual chassis group with its own unique group identifier. 
Duplicate group identifiers are not supported.

Creating the Virtual Fabric Link (VFL)

The VFL is an aggregate of high-speed ports used for inter-chassis user traffic and control data. For a 
virtual chassis group to become operational, a VFL must be configured and brought to an operational state. 

To configure a VFL and its member ports, use the 

virtual-chassis vf-link create

 and 

virtual-chassis vf-

link member-port

 commands. For example:

-> virtual-chassis vf-link 0 create

-> virtual-chassis vf-link 0 member-port 1/1

-> virtual-chassis vf-link 0 member-port 1/24

Configuring the VFL Default VLAN

Traffic belonging to the VFL default VLAN will be sent across the VFL untagged. In addition, the VFL 
automatically becomes a member of any additional VLANs configured on the virtual chassis as tagged 
VLANs. 

To configure the VFL default VLAN, use the 

virtual-chassis vf-link default-vlan

 command. For exam-

ple:

-> virtual-chassis vf-link 0 default-vlan 2

Configuring the Hello Interval

Hello packets are used for establishing and maintaining the neighbor relationship between virtual chassis 
switches and ensures that communication between switches is bidirectional. Hello packets are sent periodi-
cally out VFL interfaces. Bidirectional communication is indicated when the switch sees itself listed in the 
neighbor's hello packet. The hello interval value determines how often these packets are sent.

It is recommended that the same hello interval be used for all switches that will participate on the same 
virtual chassis topology. Failure to adhere to this recommendation will lead the switches whose values 
depart from the master chassis' settings to assume the 

Inconsistent

 role and 

Misconfigured-Hello-Interval

 

status.

Summary of Contents for os6900















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments