manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

Share
Download
NXP Semiconductors MC9S08PA4 Reference Manual Download Page 352

• BDC clock runs in stop mode, if BDC enabled
• Watchdog disabled by default while in active background mode. It can also be

enabled by proper configuration

Features of the ICE system include:

• Two trigger comparators: Two a read/write (R/W) or one full a data

+ R/W

• Flexible 8-word by 16-bit FIFO (first-in, first-out) buffer for capture information:

• Change-of-flow addresses or
• Event-only data

• Two types of breakpoints:

• Tag breakpoints for instruction opcodes
• Force breakpoints for any address access

• Nine trigger modes:

• Basic: A-only, A OR B
• Sequence: A then B
• Full: A AND B data, A AND NOT B data
• Event (store data): Event-only B, A then event-only B
• Range: Inside range (A ≤ address ≤ B), outside range (address < A or address >

B)

18.2 Background debug controller (BDC)

All MCUs in the HCS08 Family contain a single-wire background debug interface that
supports in-circuit programming of on-chip nonvolatile memory and sophisticated non-
intrusive debug capabilities. Unlike debug interfaces on earlier 8-bit MCUs, this system
does not interfere with normal application resources. It does not use any user memory or
locations in the memory map and does not share any on-chip peripherals.

BDC commands are divided into two groups:

• Active background mode commands require that the target MCU is in active

background mode (the user program is not running). Active background mode
commands allow the CPU registers to be read or written, and allow the user to trace
one user instruction at a time, or GO to the user program from active background
mode.

• Non-intrusive commands can be executed at any time even while the user's program

is running. Non-intrusive commands allow a user to read or write MCU memory
locations or access status and control registers within the background debug
controller.

Background debug controller (BDC)

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

352

NXP Semiconductors

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands