manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

Share
Download
NXP Semiconductors MC9S08PA4 Reference Manual Download Page 338

WDOG_CS1 field descriptions (continued)

Field

Description

0

Watchdog interrupts are disabled. Watchdog resets are not delayed.

1

Watchdog interrupts are enabled. Watchdog resets are delayed by 128 bus clocks.

5

UPDATE

Allow updates

This write-once bit allows software to reconfigure the watchdog without a reset.

0

Updates not allowed. After the initial configuration, the watchdog cannot be later modified without
forcing a reset.

1

Updates allowed. Software can modify the watchdog configuration registers within 128 bus clocks
after performing the unlock write sequence.

4–3

TST

Watchdog Test

Enables the fast test mode. The test mode allows software to exercise all bits of the counter to
demonstrate that the watchdog is functioning properly. See the 

Fast testing of the watchdog

 section.

This write-once field is cleared (0:0) on POR only. Any other reset does not affect the value of this field.

00

Watchdog test mode disabled.

01

Watchdog user mode enabled. (Watchdog test mode disabled.) After testing the watchdog, software
should use this setting to indicate that the watchdog is functioning normally in user mode.

10

Watchdog test mode enabled, only the low byte is used. WDOG_CNTL is compared with
WDOG_TOVALL.

11

Watchdog test mode enabled, only the high byte is used. WDOG_CNTH is compared with
WDOG_TOVALH.

2

DBG

Debug Enable

This write-once bit enables the watchdog to operate when the chip is in debug mode.

0

Watchdog disabled in chip debug mode.

1

Watchdog enabled in chip debug mode.

1

WAIT

Wait Enable

This write-once bit enables the watchdog to operate when the chip is in wait mode.

0

Watchdog disabled in chip wait mode.

1

Watchdog enabled in chip wait mode.

0

STOP

Stop Enable

This write-once bit enables the watchdog to operate when the chip is in stop mode.

0

Watchdog disabled in chip stop mode.

1

Watchdog enabled in chip stop mode.

Memory map and register definition

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

338

NXP Semiconductors

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands