manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

Share
Download
NXP Semiconductors MC9S08PA4 Reference Manual Download Page 120

SYS_SRS field descriptions (continued)

Field

Description

0

Reset not caused by POR.

1

POR caused reset.

6

PIN

External Reset Pin

Reset was caused by an active low level on the external reset pin.

0

Reset not caused by external reset pin.

1

Reset came from external reset pin.

5

WDOG

Watchdog (WDOG)

Reset was caused by the WDOG timer timing out. This reset source may be blocked by WDOGE = 0.

0

Reset not caused by WDOG timeout.

1

Reset caused by WDOG timeout.

4

ILOP

Illegal Opcode

Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP instruction is
considered illegal if stop is disabled by STOPE = 0 in the SOPT register. The BGND instruction is
considered illegal if active background mode is disabled by ENBDM = 0 in the BDCSC register.

0

Reset not caused by an illegal opcode.

1

Reset caused by an illegal opcode.

3

ILAD

Illegal Address

Reset was caused by an attempt to access a illegal address. The illegal address is captured in illegal
address register (ILLAH:ILLAL).

0

Reset not caused by an illegal address.

1

Reset caused by an illegal address.

2

LOC

Internal Clock Source Module Reset

Reset was caused by an ICS module reset.

0

Reset not caused by ICS module.

1

Reset caused by ICS module.

1

LVD

Low Voltage Detect

If the LVDRE bit is set in run mode or both LVDRE and LVDSE bits are set in stop mode, and the supply
drops below the LVD trip voltage, an LVD reset will occur. This bit is also set by POR.

NOTE: This bit reset to 1 on POR and LVR and reset to 0 on other reset.

0

Reset not caused by LVD trip or POR.

1

Reset caused by LVD trip or POR.

0

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

System Control Registers

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

120

NXP Semiconductors

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands