Nortel Meridian Installation And Administration Manual Download Page 68

Page: 68 / 256

Meridian Digital Telephone IP Adapter Installation and Administration Guide

Installing the Meridian Digital Telephone IP Adapter unit

Standard 1.1

Use both hands to push forward until the circuit card snaps into place under
the brackets.

Note:

Two holes on either side of the circuit card should now be aligned

with the corresponding holes on the footstand.

Attach the Meridian Digital Telephone Internal IP Adapter circuit card to the
footstand with the screws supplied in the Installation Kit.

Note:

Refer to “D” in the diagram on page 44.

Plug the male RJ-11 connector on the loose end of the Meridian Line Cord
attached to the Remote Office 9110 unit into the jack on the telephone.

Re-attach the footstand to the bottom of the telephone.

Apply the overlay identifying the power connection and the jack connecting
your Ethernet for IP network connectivity.

G101493

circuit card

Summary of Contents for Meridian

































































































































































































































































Search results

Summary of Contents for Meridian

Reviews:

Brands by name

Popular brands

Nortel Meridian, Installation And Administration Manual

Search results

Summary of Contents for Meridian

Reviews:

Brands by name

Popular brands