manualshive.com logo in svg

Nortel Meridian, Installation And Administration Manual

Share
Download
Nortel Meridian Installation And Administration Manual Download Page 219

Meridian Digital Telephone IP Adapter Installation and Administration Guide

195

October 2001 

Glossary 

DB9 connector

A 9-pin connector labeled ADMIN that provides the RS-232 serial port 
interface. This serial port connection can be used to configure a Remote Office 
9150 unit that is directly connected to a PC.

DB25 connector

The DB25 connector on the RLC Multi-I/O cable–Enhanced is for future use.

DC 

See

 direct current.

DHCP

See

 dynamic host configuration protocol.

digital linear tape

A high-capacity 1/2-inch streaming tape cartridge format.

digital signal processor

A special type of coprocessor that manipulates analog data, such as sound or 
photographs, that has been converted to digital form.

DIMM

See

 dual in-line memory module.

direct current

DC, the electrical power used by computers, comes from a single source (such 
as a battery) that provides a single voltage that stays at a constant level. AC, the 
power provided by utility companies, must be converted to DC before it can be 
used in computer systems.

directory number 

The number that identifies a phoneset on a switch. The directory number (DN) 
could be a local extension (local DN), a public network telephone number, or an 
automatic call distribution directory number (ACD-DN).

DIP 

A type of protective packaging for silicon memory chips that provides a safe and 
convenient means of installing and removing the chip.

Summary of Contents for Meridian

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands