manualshive.com logo in svg

Nortel Meridian, Installation And Administration Manual

Share
Download
Nortel Meridian Installation And Administration Manual Download Page 227

Meridian Digital Telephone IP Adapter Installation and Administration Guide

203

October 2001 

Glossary 

IP address

Internet Protocol address. An identifier for a computer or device on a TCP/IP 
network. Networks use the TCP/IP protocol to route messages based on the IP 
address of the destination. The format of an IP address is a 32-bit numeric 
address written as four numbers separated by periods. Each number can be 
0–255. For example, 1.160.10.240 could be an IP address. 

IPX

Internetwork Packet Exchange. A networking protocol used by the Novell 
NetWare operating systems.

ISA

See

 Industry Standard Architecture. 

ISDN

See 

integrated services digital network.

J  

jumper

A metal bridge that closes an electrical circuit. Typically, a jumper consists of a 
plastic plug that fits over a pair of protruding pins. Jumpers are sometimes used 
to configure expansion boards. By placing a jumper plug over a different set of 
pins, you can change a board’s parameters. 

K  

Kbyte

See

 kilobyte.

kilobyte

1024 bytes. Roughly the amount of information in half a typewritten page.

L  

LAN

See

 local area network. 

LCD

Liquid crystal display. An alphanumeric display using liquid crystal sealed 
between two pieces of glass.

Summary of Contents for Meridian

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands