manualshive.com logo in svg

Nortel Meridian, Installation And Administration Manual

Share
Download
Nortel Meridian Installation And Administration Manual Download Page 220

196

Meridian Digital Telephone IP Adapter Installation and Administration Guide

Glossary

 Standard 1.1

DIP switch

A series of tiny switches built into circuit boards that enables you to configure a 
circuit board for a particular type of computer or application. DIP switches are 
always toggle switches. This means that they have two possible positions: on or 
off (or 1 or 0).

direct memory access

DMA speeds up system performance by moving blocks of memory around 
inside the computer (typically between I/O devices and memory). This process 
enables the microprocessor to spend its time performing other functions. 

DLL 

See

 dynamic link library.

DLT

See

 digital linear tape.

DMA

See

 direct memory access.

DN

See

 directory number.

driver

A program that controls a device. Every device, whether it is a printer, disk 
drive, or keyboard, must have a driver program. A driver acts like a translator 
between the device and programs that use the device. 

DSP

See

 digital signal processor.

dual in-line memory module

The protective packaging for microprocessor chips that provides a safe and 
convenient means of installing and removing the chip.

dynamic host configuration protocol

A protocol for dynamically assigning IP addresses to devices on a network. 

Summary of Contents for Meridian

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands