Nortel 1000BASE-XD Using Manual Download Page 38 | Manualshive

Page: 38 / 100

background image

Using the Passport 8100 Modules

2-2

204515-C

Chassis Configuration Requirements

Slots in the Passport 8000 Series chassis are numbered from the top down, starting
with 1. In either the Passport 8010 or the Passport 8006 chassis, slots 5 and 6 are
reserved for the Passport 8190SM Switch Management Module. Any of the
Passport 8100 Series I/O modules can be installed in the remaining chassis slots.

Safety and Environmental Precautions

Before you perform any installation or replacement procedure on the switch,
please note the following safe-handling guidelines:

•

To prevent damage caused by electrostatic discharge (ESD), handle the switch
chassis and modules only when you, the chassis, and the chassis modules are
properly grounded. Nortel Networks recommends using a grounding wrist
strap.

•

When handling modules, do not touch components on the circuit boards;
always handle modules by their edges. Store unused modules in their
protective packaging.

•

To maintain proper airflow and cooling, always cover unused module slots
and power supply bays with filler panels.

Note:

You must install an I/O module in slot 1 or slot 2 to provide bus master

functions in the switch.

«
...
36
37
38
39
40
...
»

Summary of Contents for 1000BASE-XD





































































































Reviews:

No comments

Related manuals for 1000BASE-XD

Brand: Tailfin Pages: 4

Brand: omnicharge Pages: 12

Brand: omnicharge Pages: 72

Brand: Vega Pages: 2

Brand: Vega Pages: 11

Brand: Rice Lake Pages: 2

Brand: Carinae Sports Pages: 22

Brand: Elk Products Pages: 2

Brand: Elk Pages: 2

Brand: Olympus Pages: 43

Brand: Polaroid Pages: 64

Brand: SRAM Pages: 26

Brand: SimpliPhi Pages: 15

Classic Studex Mk2 G1326 G1326

Brand: Gitzo Pages: 1

Brand: ZiFiSense Pages: 14

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

X-903 Ultra Carbon 29

Brand: X-lite Pages: 116

Brand: Orno Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands