manualshive.com logo in svg

Nortel 1000BASE-XD, Using Manual

Share
Download
Nortel 1000BASE-XD Using Manual Download Page 52

Using the Passport 8100 Modules

3-8

204515-C

Switch Configuration

The Passport 8100 Series modules provide layer 2 switching as soon as you install 
them and turn on the switch power. The default configuration includes a single 
VLAN with a VLAN ID of 1 that contains all the ports in the switch. 

The only configuration you need to do for the Passport 8100 Series switch is to 
assign an IP address and a gateway address (default route) for remote 
management.

Configuring the Passport switch as a layer 2 switch consists of the following 
tasks:

•

Confirm that all ports are in the default VLAN.

•

Assign an IP address for management.

•

Specify a default gateway address or default route.

•

Test connectivity.

To configure the switch as a layer 2 (bridging/switching) device:

1.

Confirm that all ports are in the default VLAN using the command:

show vlan info ports 

The display shows the VlanId (1) and lists the port members.

2.

To assign an IP address for management, use the command:

config bootconfig net mgmt ip <ipaddr/mask>

where:

<ipaddr/mask> 

is the IP address/subnet mask you are assigning (for 

example, 10.10.10.1/24).

Alternatively, you can assign an IP address to the default VLAN (VLAN ID 
1) using the command 

config vlan 1 ip create <addr/mask>

.

Note: 

Nortel Networks does not recommend assigning an IP address to 

the default VLAN. Management response is significantly degraded by 
managing the switch through the default VLAN.

Summary of Contents for 1000BASE-XD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands