manualshive.com logo in svg

Nortel 1000BASE-XD, Using Manual

Share
Download
Nortel 1000BASE-XD Using Manual Download Page 78

Using the Passport 8100 Modules

B-2

204515-C

Table B-1.

LED Operation on the Passport 8190SM Module

Label

Color/State

Meaning

Link

Green/Steady

The management port is connected, and the link is 
good.

Off

There is no link to the management port.

100

Green/Steady

The management port is operating at 100 Mb/s.

Off

The management port is operating at 10 Mb/s.

Utilization %
(8 LEDs)

Green

The number of lit LEDs indicates the level of CPU 
activity.

Power Supply 
1, 2, 3

Off

A power supply is not present in the specified 
position, or the power supply in the specified 
position is not turned on.

Green/Steady

The specified power supply is operating normally.

Amber/Steady

The specified power supply has a fault.

Fan 1, 2

Green/Steady

The specified fan is operating normally.

Amber/Steady

The specified fan has failed.

Temp

Green/Steady

The temperature is normal for switch operation.

Amber/Steady

The maximum operating temperature has been 
exceeded.

Master

Off

The CPU subsystem on the module is performing 
diagnostics.

Amber/Steady

The CPU subsystem is in a fault state.

Green/Blinking

This module is providing active CPU functions for 
the switch.

Green/Steady

The CPU subsystem on this module is up and in 
standby mode.

Online

Off

This LED is always off during operation of the 
Passport 8190SM module.

Summary of Contents for 1000BASE-XD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands