manualshive.com logo in svg

Nortel 1000BASE-XD, Using Manual

Share
Download
Nortel 1000BASE-XD Using Manual Download Page 34

Using the Passport 8100 Modules

1-14

204515-C

Redundant Passport 8190SM Modules

When you install two Passport 8190SM modules in a Passport 8000 Series 
chassis, one provides the active CPU functions for the switch; the CPU subsystem 
on the other module is in standby mode. If the active CPU fails, the standby CPU 
assumes the CPU functions for the switch within 1 second. Then the module 
relearns the routing databases for the switch. 

If two Passport 8190SM modules are installed in the chassis when you turn on 
switch power, the module in slot 5 becomes the active CPU; the module in slot 6 
is in standby mode.

Redundant Power Supplies

A Passport 8000 Series chassis supports redundant power supplies. Both AC and 
DC power supplies are available, and they may be combined in the same chassis. 

The Passport 8010 Chassis with more than six installed modules requires a 
minimum of two power supplies for a nonredundant configuration. A redundant 
configuration for such a chassis requires three power supplies.

In a chassis with a nonredundant power supply configuration, if one power supply 
fails, the system loses power and network connectivity.

In a chassis with two installed power supplies, you can add a third power supply 
without removing power to the chassis. In a chassis with a redundant power 
configuration, you can hot-swap any one power supply while the chassis 
continues to operate with no interruption of service (

Table 1-1

).

Summary of Contents for 1000BASE-XD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands