Nortel 1000BASE-XD Using Manual Download Page 91

Page: 91 / 100

204515-C

D-1

Appendix D

Installing GBICs

This appendix describes how to install the gigabit interface converters (GBICs) in
the Passport 8108GBIC module.

The following GBIC versions are available for the Passport 8108GBIC switch
module:

•

100BASE-SX—uses multimode fiber over distances up to 550 meters

•

100BASE-LX—uses multimode fiber over distances up to 550 meters or
single-mode fiber over distances up to 10 kilometers (km)

•

100BASE-XD—uses single-mode fiber over distances up to 50 km

•

100BASE-ZX—uses single-mode fiber over distances up to 70 km

GBICs are available in two styles (

Figure D-1

). One type has two spring tabs at

the front of the GBIC; the other type has an extractor handle on the front.

Figure D-1.

Types of GBICs

GBICs are shipped with a protective rubber plug in the connectors. Leave the plug
in place when no cables are connected to the GBIC.

9702FA

Summary of Contents for 1000BASE-XD





































































































Search results

Summary of Contents for 1000BASE-XD

Reviews:

Related manuals for 1000BASE-XD

Brands by name

Popular brands

Nortel 1000BASE-XD, Using Manual

Search results

Summary of Contents for 1000BASE-XD

Reviews:

Related manuals for 1000BASE-XD

Brands by name

Popular brands