Nortel 1000BASE-XD Using Manual Download Page 63

Page: 63 / 100

204515-C

A-1

Appendix A

Technical Specifications

This appendix lists technical specifications for the Passport 8100 modules. The
appendix includes the following information:

•

General specifications

•

Specifications for individual modules, including:

— Physical specifications

— Connector types and, where appropriate, pin assignments

— Required cables

•

MDI and MDI-X connections

•

Declaration of Conformity

General Specifications

Standards Supported

IEEE 802.3 CSMA/CD (ISO/IEC 8802-3)

IEEE 802.3i 10BASE-T (ISO/IEC 8802-3)

IEEE 802.3u 100BASE-TX (ISO/IEC 8802-3)

IEEE 802.1D MAC Bridges (ISO/IEC 10038)

IEEE 802.1p (Prioritization)

IEEE 802.1Q (VLAN Tagging)

IEEE 802.1z (Gigabit)

IEEE 802.3z 1000BASE-SX and 1000BASE-LX (Draft Standard ver. 3.1)

IEEE 802.3x on Gigabit ports

Summary of Contents for 1000BASE-XD





































































































Search results

Summary of Contents for 1000BASE-XD

Reviews:

Related manuals for 1000BASE-XD

Brands by name

Popular brands

Nortel 1000BASE-XD, Using Manual

Search results

Summary of Contents for 1000BASE-XD

Reviews:

Related manuals for 1000BASE-XD

Brands by name

Popular brands