Nortel 1000BASE-XD Using Manual Download Page 23

Page: 23 / 100

About the Passport 8100 Modules

204515-C

1-3

•

IEEE 802.1Q port-based virtual LANs (VLANs)

•

IEEE 802.1p prioritization

•

IEEE 802.3u-compliant autonegotiating ports, with four modes:

— 10BASE-T half-duplex

— 10BASE-T full-duplex

— 100BASE-TX half-duplex

— 100BASE-TX full-duplex

•

Two hardware-based priority queues per port

•

Multi-Link Trunking (MLT) with up to 4 ports in a trunk and up to 6 MLT
groups in a switch with a single trunk able to span multiple I/O modules,
supporting switch-to-switch trunks and switch-to-server trunks

•

Ability to remove and install a module (hot swap) without powering down the
switch chassis

•

Port mirroring by port, by source, and by destination MAC address

•

IP Multicast optimization using Internet Group Management Protocol
(IGMP) snooping

•

RMON port support for the following four groups:

— Alarms

— Events

— Statistics

— History

•

Port for configuring and managing the switch locally or remotely:

— Console port on the Passport 8190SM module

— Ethernet Management port on the Passport 8190SM module

— Comm port on the Passport 8132TX module (if a Passport 8190SM

module is not installed)

Summary of Contents for 1000BASE-XD





































































































Search results

Summary of Contents for 1000BASE-XD

Reviews:

Related manuals for 1000BASE-XD

Brands by name

Popular brands

Nortel 1000BASE-XD, Using Manual

Search results

Summary of Contents for 1000BASE-XD

Reviews:

Related manuals for 1000BASE-XD

Brands by name

Popular brands