manualshive.com logo in svg

Nortel 1000BASE-XD, Using Manual

Share
Download
Nortel 1000BASE-XD Using Manual Download Page 80

Using the Passport 8100 Modules

B-4

204515-C

Table B-2

 describes the module LEDs, and 

Table B-3

 describes the port LEDs.

Passport 8108GBIC Module

The Passport 8108GBIC module has three LEDs to indicate module and system 
operating conditions (

Table B-4

). In addition, each port has two LEDs to indicate 

the presence of link and data activity (

Table B-5

). 

Figure B-3

 shows the locations 

of the LEDs.

Table B-2.

Module LEDs on the Passport 8132TX and 8148TX Modules

Label

Color/State

Meaning

Fault

Yellow/Steady

A diagnostics failure or hardware failure has been detected.

Yellow/Blinking

A chassis failure has been detected.

Off

The system is functioning normally.

Master

Green/Steady

This module is properly generating the system clock for the switch.

Yellow/Steady

This module has detected system clock generation failure on its own 
circuitry.

Off

This module is not providing the system clock for the switch. You can pull 
this module out of the chassis without resetting the switch.

Online

Green/Steady

The module is functioning normally and is in switching mode.

Green/Blinking

The module is running diagnostic tests.

Yellow/Steady

The module is not in switching mode.
Software incompatibility exists, or the module cannot communicate with the 
master module over the backplane.

Off

The module is not receiving power or is administratively disabled.

Table B-3.

Port LEDs on the Passport 8132TX and 8148TX Modules

LED

Color/State

Meaning

10/100 
(Speed)

Green/Steady

The port is set to operate at 100 Mb/s.

Off

The port is set to operate at 10 Mb/s.

Link/Activity

Off

No link exists, or the port is disabled.

Green/Steady

The link is good.

Green/Blinking

The link is good, and the port is transmitting or receiving traffic.

Summary of Contents for 1000BASE-XD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands