Nordson Spectrum II S2-900 C Series, Installation, Operation And Maintenance Manual

Page: 261 / 262

Index I-3
Low Fluid Sensor ............................................................. 1-8
Low Pressure Detection Threshold ............................... 4-10
Low Pressure Sensor ....................................................... 1-9
Lubricating the Cables................................................... 6-13
Lubricating the X/Y Linear Guides ................................. 6-15
M
Machine Offsets ............................................................ 4-28
valve offsets ............................................................. 4-21
Main Circuit Breaker ..................................................... 2-14
Maintenance
draining the water trap .............................................. 6-7
lubricating the cables ............................................... 6-13
lubricating the X/Y linear guides .............................. 6-15
purge station ....................................................... 6-4, 6-6
record keeping .................................................... 5-1, 6-1
replacing consumables ............................................... 6-3
routine procedures .................................................... 6-2
tensioning the conveyor belts .................................. 6-25
tensioning the X/Y cables ......................................... 6-17
tensioning the Z cables ............................................ 6-18
verifying interlock functionality ................................. 6-8
weigh station .............................................................. 6-4
Manual Dual-Simultaneous Dispensing (MDS) ............... 1-7
Manuals .......................................................................... 1-2
Mass Flow Calibration .............................................. 1-5, 1-9
Material Safety ............................................................... 2-3
MFC ............................................. See Mass Flow Calibration
N
Needle Heater
setting the temperature ........................................... 4-37
troubleshooting ....................................................... 7-12
O
Ordering Parts ................................................................. 8-1
P
Parts Replacement
conveyor belts ............................................................ 8-4
credit and exchanges ................................................. 8-2
record keeping ........................................................... 8-2
replacing the height sensor probe ........................... 8-10
return material authorization .................................... 8-2
unpacking replacement parts .................................... 8-2
Pattern
creating .................................................................... 4-43
placing ...................................................................... 4-44
Pneumatics
adjusting the main air pressure ................................. 4-5
connections .............................................................. 3-13
cooling, valve, fluid pressure adjustment .................. 4-7
setting the low pressure threshold .......................... 4-10
tooling, pressure adjustment ..................................... 4-6
vacuum control adjustment ..................................... 4-10
Power Manager ....................................................... 1-9, B-2
Powering on the Dispensing System ...............................
4-2
Pre- and Post-Queue Stations ......................................... 1-9
Process Development Hot Plate ...................................... 1-9
Production Run
dry mode .................................................................. 4-46
Program
creating ............................................................ 4-27–4-46
testing ....................................................................... 4-46
Program Commands ...................................................... 4-38
Program Commands Toolbar
dispensing elements ................................................. 4-40
Programmable Tilt and Rotate ...................................... 1-10
Purge Boot
replacement ............................................................... 6-6
Purge Station ................................................................. 1-10
boot replacement ....................................................... 6-6
cup replacement ......................................................... 6-4
R
Rear Panel Connections ................................................ 1-25
Record Keeping .......................................... 5-1, 6-1, 7-1, 8-2
Removing Rear Cable Covers ......................................... 6-12
Return Material Authorization ........................................ 8-2
S
S2-9XXC Cleanroom System ............................................ 1-6
front view ................................................................. 1-14
house vacuum ................................................. 1-25, 3-14
lubricating cables ...................................................... 6-13
scale .......................................................................... 1-17
Safe Z-height ................................................................. 4-25
Safety .............................................................................. 2-1
beacon color indicatons ........................................... 2-18
earthquake precautions ............................................. 2-5
equipment lockout/tagout ....................................... 2-16
intended use ............................................................... 2-1
laser radiation ............................................................. 2-3
lifting and transport precautions ................................ 2-5
material safety ............................................................ 2-3
misuse ........................................................................ 2-2
personnel safety ......................................................... 2-2
residual safety risks .................................................. 2-12
SDS .............................................................................. 2-3
service shutdown...................................................... 2-16
warning labels ................................................... 2-6–2-11
Safety Data Sheet ............................................................ 1-1
Moly-Graph Extreme Pressure Grease ....................... A-8
Multemps PS NO 2 ...................................................... A-2
NSK Clean Grease LG2 .............................................. A-15
Safety Data Sheets .......................................................... 2-3
Safety Interlock ............................................................. 2-15
recovery .................................................................... 2-15
Safety Warning Labels ............................................ 2-6–2-11
Scale .............................................................................. 1-17
calibration ................................................................... 5-8
cleanroom ................................................................ 1-17
cup replacement ......................................................... 6-4
installation .................................................................. 3-4
troubleshooting ........................................................ 7-10
SDS .................................................... See Safety Data Sheet