manualshive.com logo in svg

Nordson Encore LT, Product Manual, Page: 85 / 92

Share
Download
Nordson Encore LT Product Manual Download Page 85

Parts

7-17

Part 1604857-04

E

 2014 Nordson Corporation

Optional Transportable Manual System 

This system consists of an Encore LT manual powder spray system packed

into a case for transportation. The following parts list consists of

replacements for the components in the system.

Part

Description

Quantity

Note

1602351

SYSTEM, transportable, Encore LT

1

1602463

S

CASE, transportable, Encore LT

1

1106893

S

HANDGUN assembly, manual, Encore LT

1

1107552

S

CONTROLLER ASSY, manual, Encore LT, packaged

1

1095922

S

PUMP assembly, corona, Encore Gen II, packaged

1

1100777

S

KIT, cup gun, Encore

1

1082060

S

NOZZLE, conical, Encore

1

1083206

S

DEFLECTOR assembly, conical, 26 mm, Encore

1

1083201

S

DEFLECTOR assembly, conical, 16 mm, Encore

1

1082185

S

NOZZLE, cross

−

cut, 2.5 mm, 90 degree, Encore

1

1081656

S

NOZZLE, flat spray, 2.5 mm, Encore

1

1081659

S

NOZZLE, flat spray, 6 mm, Encore

1

1085679

S

KIT, pump adapter, hopper, Encore

1

1082204

S

COUPLING, pump, Encore

1

768176

S

TUBING, powder, antistatic, 11 mm (.43 in)

6 ft

A

900740

S

TUBING, polyurethane, 10/6.5

−

7 mm

6 ft

B

900517

S

TUBING, spiral cut, .62 in. ID

1.5 ft

C

900742

S

TUBING, polyurethane, 6/4 mm, blue

6 ft

B

972262

S

REDUCER, 10 mm stem

1

1081658

S

NOZZLE, flat spray, 4 mm, Encore

1

D

NOTE A: Minimum order quantity is 100 ft.

B: Minimum order quantity is 50 ft.
C: Order in increments of one foot.
D: 4-mm flat spray nozzle is shipped with the spray gun.

Figure 7-14 Encore LT Transportable System

Summary of Contents for Encore LT





























































































Reviews:

No comments