background image

Parts

7-15

Part 1604857-04

E

 2014 Nordson Corporation

System Components and Parts 

1

1A

3

2

Figure 7-13 Miscellaneous System Parts

Item

Part

Description

Quantity

Note

1

1097809

TUBE, fluid, pickup, w/cond. fitting, VBF, Encore

1

1A

1096788

S

CONN, 6mm tube x R 

1

/

8

, dia 0.7mm orifice

1

D

2

1084760

ISOLATOR, vibration, 1.0 dia x 1.5 x 

5

/

16

 studs

3

A

3

1108090

VIBRATOR, electric, 115V, 60 Hz, w/cord grip

1

A

3

1108091

VIBRATOR, electric, 230V, 50 Hz, w/cord grip

1

A

NS

1107552

CONTROLLER, manual, Encore LT, packaged

1

NS

1095922

PUMP assembly, corona, Encore Gen II

1

NS

1106893

HANDGUN ASSY, Encore LT

1

NS

1107949

HOPPER, NHR Encore, 50-lb

1

B

NS

972841

CONN, male, 10 mm tubing x 1/4 unithread

1

NS

1093708

GROMMET, 0.719 ID x 1.281 OD x 0.093 GR

1

NS

134575

WIRE, ground (with ground clamp)

1

NS

1107895

KIT, VBF pickup tube arm assembly, Encore LT

1

A

NS

1107903

S

KIT, pickup tube collar, Encore LT

1

A

NS

1107913

KIT, rail mount, Encore LT

1

NS

1600437

KIT, wall mount, Encore LT

NS

1067694

KIT, ground bus bar, ESD, 6 position, w/hardware

1

C

NS

1085679

KIT, pump adapter, hopper, Encore

1

C

NS

1082204

COUPLING, pump, Encore

1

C

NS

972262

REDUCER, 10 mm stem x 6 mm tubing

1

F

NS

1600658

HANGER, gun, Encore LT

1

NS

1600566

KIT, filter, Encore LT

1

E

NS

1600608

S

FILTER, mist separator, 0.3 micron, 1/2 in. NPT

1

E

NS

1600609

S S

FILTER ELEMENT, separator, 0.3 micron

1

NS

1604487

VALVE, flow control, 4-mm tube x 4-mm tube

1

G

NOTE A: VBF systems only. Order the correct vibrator motor for your VBF system.

B: Hopper systems only. Hopper includes pickup tube.
C: Included with both wall- and rail-mount systems.
D: Conductive fitting. Do not replace with a non-conductive fitting.
E: Filter kit includes fittings and mounting bracket.  Order filter only to replace mobile system filter.
F: Install in hopper plenum elbow.
G: Connect to air wash connector on controller rear panel to control air flow.

NS: Not Shown

Summary of Contents for Encore LT





























































































Reviews: