Nordson Encore LT Page 44 Product Manual Download

Page: 44 / 92

Operation

4-10

Part 1604857-04

2014 Nordson Corporation

Changing Flat Spray Nozzles

WARNING:

Release the spray gun trigger, put the controller to sleep, and

ground the electrode before performing this procedure. Failure to observe

this warning could result in a severe electrical shock.

NOTE:

The tapered electrode holder of the electrode assembly has been

designed for optimized cleaning during color changes on systems using flat

spray nozzles. This tapered electrode holder will not accept conical

deflectors.
1. Purge the spray gun and press the Enable/Disable button to put the

controller to sleep in order to prevent accidental gun triggering.

2. See Figure 4-7. Unscrew the nozzle nut counterclockwise.
3. Pull the flat spray nozzle off the electrode assembly.

NOTE:

Re-install the electrode assembly if it comes out of the powder

outlet tube.
4. Install a new nozzle on the electrode assembly. The nozzle is keyed to

the electrode assembly. Do not bend the antenna wire.

5. Screw the nozzle nut onto the gun body clockwise until finger-tight.
6. Press the Enable/Disable button to wake up the controller.

NOTE:

To clean nozzles, use the

Recommended Cleaning Procedure for

Powder Contact Parts

on page 4-13.

Nozzle Nut

Flat Spray Nozzle

Electrode Assembly

Figure 4-7

Changing a Flat Spray Nozzle

Summary of Contents for Encore LT





























































































Search results

Summary of Contents for Encore LT

Reviews:

Related manuals for Encore LT

Brands by name

Popular brands

Nordson Encore LT, Product Manual

Search results

Summary of Contents for Encore LT

Reviews:

Related manuals for Encore LT

Brands by name

Popular brands